_

In order to start driving you should log into the system via one of the following ways:

you should have the key fob or smartphone (paired to the system)
enter the PIN-code using the standard vehicle buttons

If the key fob was detected (PIN-code was entered correctly), the system will signal with indication, the engine will not be locked and you can start driving.

If the key fob was not detected (PIN-code was incorrect or was not entered at all), IGLA will lock the engine. The locking method (engine start inhibit and/or locking of the running engine) depends of the IGLA system settings and the car brand/model.

The security system is activated in 10 seconds after the ignition is off.

Authorization with the key fob or with smartphone

Do not leave the key fob (smartphone) inside the car when the ride is over. Otherwise the anti-theft functions will be deactivated.

In order to log into the system it is enough to have the key fob or smartphone paired to the system. You can register 2 key fobs and 2 smartphones in the IGLA system memory. For authorization in the system you need to have with you at least one registered device.

Get into the car and start up the ignition. When the key fob/smartphone is detected, the system will give out two verification signals , after that you can start driving.

If the key fob/smartphone is not detected, there will be no verification signals and if one attempts to start driving or start up the ignition, the engine will be locked.

Authorization with the PIN-code

The authorization method depends on the chosen way of engine locking:

If the system inhibits the engine start, the PIN-code should be entered before the start of the engine.
If the system does not inhibit the engine start, the PIN-code can be entered both before the start of the engine or after.

The initial PIN-code is set by the specialists of the service centre. Before running the system for the first time change the PIN-code and memorize a new one.

Get into your car, start up the ignition, start the engine if needed and enter the PIN-code using the standard vehicle buttons . It is recommended to enter the PIN-code right before the ride. The interval between the pressing of the buttons shall not exceed 2 seconds. There is no difference between long and short press of the button.

After you enter the correct PIN-code there will be 2 indication signals and you can start driving.

If the PIN-code is not correct, there will be no confirmation signals and if one attempts to start driving or start up the ignition, the engine will be locked. The second attempt to enter the PIN-code is available in 5 seconds after the failed attempt to log in or after turning off the ignition for 10 seconds and starting the ignition again.

Step-by-step authorization

In step-by-step authorization mode to start driving the car you need to go through two authorization stages:

You must have with you the key fob or smartphone used as a key fob when you switch on the ignition. Starting the engine will be allowed (even if the system is switched to engine start inhibit), however IGLA will shut off the engine when you try to drive while no PIN-code was entered.
To complete the authorization, you must enter PIN-code via standard buttons in the car.

Step-by-step authorization is possible only when stall of the running engine via CAN or analog contour is used.

By default, step-by-step authorization mode is disabled in the system. To enable this mode, activate the corresponding menu item:

Switch on the ignition without starting the engine and enter the PIN-code to authorize.
Press the accelerator pedal as far as it can go and keep it pressed.
Press the service button 23 times. 23 indication signals will confirm that step-by-step authorization mode is activated.
Release the accelerator pedal.

The system will disable step-by-step authorization if:

If you choose another authorization mode
If you erase key fobs/smartphones from the system memory
If you reset the PIN-code

Two-factor authorization

To provide the maximum level of security you can use two-factor authorization mode in IGLA system. In this mode, the engine can be started only if two conditions are observed:

The car owner has key fob or smartphone with him
PIN-code is entered via standard buttons in the car

By default, two-factor authorization mode is disabled in the system. To enable this mode, activate the corresponding menu item:

Switch on the ignition without starting the engine and enter the PIN-code to authorize.
Press the accelerator pedal as far as it can go and keep it pressed.
Press the service button 24 times. 24 indication signals will confirm that two-factor authorization mode is activated.
Release the accelerator pedal.

The system will disable two-factor authorization if:

If you choose another authorization mode
If you erase key fobs/smartphones from the system memory
If you reset the PIN-code