IGLA PIN-code setting

Device number check

This check is necessary to confirm the connection between the plastic card with codes and the installed device. If the open code card number does not match with the device, the only way to change the forgotten PIN-code for the new one will only be possible in a specialized service centre.

It is recommended to do this check right after one gets the car with the installed anti-theft system IGLA from the service centre.

  1. Switch on the ignition without starting the engine.
  2. Press the brake pedal and while keeping it pressed press the accelerator pedal a certain number of times as far as it can go where the number is equal to the first figure in the open card number (indicated on the plastic card). Release the brake pedal. The first figure of the open code will be entered.

  3. Input all the rest figures of the open code in the same way (see item 2).

If the code number is correct, the system will signal with 2 flashes. If nothing happens, that means the number was entered incorrectly or it does not match with the installed device number.

Change of PIN-code

The PIN-code set in the service centre shall be changed when the car-owner get his/her car back from the service centre with the anti-theft system IGLA installed.

Also it is recommended to change the PIN-code if you suspect someone has watched you entering the PIN-code.

  1. Switch on the ignition without starting the engine.
  2. Enter the current PIN-code to authorize. There will be 2 indication signals.
  3. Press the accelerator pedal as far as it can go and keep it pressed.

  4. Enter the current PIN-code once again. The device will pass to the PIN-code change mode and the indication signals will start flashing every 3 seconds. Release the accelerator pedal.

    If the current PIN-code includes «Slight touch on accelerator pedal», after the authorization (item 2) it is necessary to enter the PIN-code once again and then press the accelerator pedal as far as it can go and keep it pressed until indication appear. Then perform item 5.

  5. Enter the new PIN-code using the buttons available for programming (see IGLA Annex). Every click will be followed by the indication signal.
    The number of clicks shall be in the range from 3 to 20 clicks. The interval between clicks shall not be more than 2 seconds. There is no difference between long and short press of the button.
    Different combinations of buttons and their order can be used, e.g. if you press CRUISE ON/OFF two times and press CRUISE SET- once, the system will save all the clicks in this order. When the PIN-code is entered there will be 3 indication signals.
  6. Enter the current PIN-code once again. If PIN-codes match then there will be 2 indication signals and the PIN-code will be successfully saved.
    If there are 4 indication signals, it means the PIN-code do not match and the PIN-code has not been saved. Turn off the ignition for 3 sec. and repeat the items 1-6.
  7. Turn off the ignition.

Memorize the PIN-code or write it down after it has been changed. Do not leave the PIN-code and the plastic card with the secret code inside the car!

PIN-code emergency resetting

In case the current PIN-code is lost the car-owner can reset it and set the new one.

In order to reset the PIN-code one needs the plastic card with an individual emergency code, hidden under the protective layer. The card is a part if the anti-theft system IGLA. Prepare the card before the PIN-code resetting procedure.

  1. Switch on the ignition without starting the engine.

    If the IGLA is aligned with the KEYLESS BLOCK module, in order for them to be disarmed by the same key fob, a ten second pause should be taken after the igniution has been turned-on.

  2. Press the brake pedal and while keeping it pressed press the accelerator pedal a certain number of times as far as it can go where the number is equal to the first figure in the emergency code. Release the brake pedal. The first figure of the code will be entered.

  3. Input all the rest figures of the emergency code in the same way (see item 2).

If the PIN-code is correct, the device will pass into the PIN-code change mode and will give out indication signal every 3 seconds. If there is no indication, the code is incorrect. In this case turn off the ignition and repeat the steps for resetting.

If the resetting was successful and the device switched to the PIN-code changing mode please enter the new PIN-code (3-20 clicks). Different combinations of buttons and their order can be used, e.g. if you press CRUISE ON/OFF two times and press CRUISE SET- once, the system will save all the clicks in this order. When the PIN-code is entered there will be 3 indication signals. Enter your PIN-code once again.

If PIN-codes match then there will be 2 indication signals. The device saves the new PIN-code and switches to the standard mode. If there are 4 indication signals, it means the PIN-code do not match. In this case repeat all of the steps for PIN-code resetting, beginning with step 1.